2019 Good Quality Hv Test - HV Shielded Test Room – LINT TOP

2019 Good Quality Hv Test - HV Shielded Test Room – LINT TOP

Product Details

FAQ

Product Details

Good quality To start with,and Purchaser Supreme is our guideline to offer the top service to our customers.Presently, we've been seeking our best to be amongst the top exporters inside our industry to fulfill consumers extra need to have for Cable Wire Recycling Machine, Laser Wire Marking System, Continuous Casting Manufacturers, We welcome buyers, business enterprise associations and good friends from all sections in the planet to get hold of us and request cooperation for mutual gains.
2019 Good Quality Hv Test - HV Shielded Test Room – LINT TOP Detail:

1. Introduction

The HV partial discharge hall is mainly used for power transformer, HV inductor, arrester, HV switch, HV XLPE cable and so on, the shielded room is used for avoiding electromagnetic interference which can affect partial discharge test.

2. Technical Parameters

Rated Voltage (kV)

±100-2000 (and above)

Exterior Dimension (m)

60*40*30(L*W*H)(bigger size is available)

Grounding Resistor

Requirement<1.0Ω

Insulating Resistance

≤10KΩ(measured after completing shielding room, insulating ground mainly used fro HV cable partial discharge hall, because there is a high requirement for partial discharge of HV cable with large capacity)

Partial Discharge

≤2.0 PC(Shielding hall partial discharge value is below 2 PC if equipment can reach below 2.0PC)

Magnetic Field

10kHZ attenuation 60dB linearity rise to 100KHZ, attenuation 100dB

Electric Field

From 1kHZ to 100kHZ attenuation 100dB


Product detail pictures:


Related Product Guide:

Innovation, excellent and reliability are the core values of our company. These principles today much more than ever form the basis of our success as an internationally active mid-size business for 2019 Good Quality Hv Test - HV Shielded Test Room – LINT TOP , The product will supply to all over the world, such as: Zambia, Jersey, Auckland, We insist on the principle of "Credit being primary, Customers being the king and Quality being the best", we are looking forward to the mutual cooperation with all friends at home and abroad and we will create a bright future of business.

FAQ

Q: Can I visit your factory?

A: All the customers from both home and abroad are warmly welcomed to visit our company and factory.

Q: Do you supply the installation and commissioning?
A: Yes, we do as followings:
-As soon as customer informed us the machines are put in the right place, we will send both mechanical and electrical engineer for machine start up.
-No-load testing: After machine installed completely, we make no-load testing first.
-With-load testing: Usually we will can produce 3 different wires to make load testing.

-Acceptance report: After the buyer confirms that machine can reach all specification under contract, the acceptance report will be signed for our record that machine will be in guarantee period.

Q: What information should I offer to get a detailed quotation from you?
A: For single machine: Usually we need to know inlet wire size, outlet wire size to be produced, productivity, pay off and take up size to choose the right machine.
For new cable plant or new cable production line, we need to know the datasheet of cables to be produced, the productivity, the standards to be followed, etc to design all machines needed.

Q: Can you supply the auxiliary equipment along with the machines?
A: Yes, definitely.
We has supplied heat exchanger, copper/aluminum powder filter machine, cooling tower, chiller, air compressor, drawing dies, pointing machine, cold welders, bobbins etc. with our machines.

Q: Could you do the design for the whole plant?
A: Yes, this is our advantage.
With the data sheet of cable to be produced, the standard your cables should follows, the productivity you expected. Our engineer on production technology and machinery will make design of production machines, test equipment, accessories like bobbins, dies, rewinding lines and materials needed.

Q: How can I know the status of my order?
A: We have our OA system on tracking the production.
For any of your request we can send photos and videos of your order, also we can use FACETIME to let you know the production.

Q: How do you work on the inspection before delivery?
A: We will make dynamic balance testing, levelness testing, noise testing, etc. during production.
After production finished, usually we make no-load running of each machine before delivery. Customers are welcomed to attend the inspection.

Q: What exhibitions will you attend, can we meet in the fair?
A: Dusseldorf International Wire and Cable Fair;
Wire South America Fair;
International Wire and Cable Fair in Shanghai;
International Istanbul Wire Fair, etc.
wire Southeast Asia Fair, etc.

Send your message to us:

Write your message here and send it to us