2019 wholesale price Lan Cable Drawing Line - Aluminum / Aluminum Alloy Rod CCR Line – LINT TOP

Product Details

FAQ

Product Details

Our well-equipped facilities and excellent excellent management throughout all stages of creation enables us to guarantee total buyer satisfaction for horizontal tensile tester, Wire Bunching Machine, argon arc welding and corrugation cable production line, We're searching ahead to setting up long-term company associations with you. Your comments and solutions are remarkably appreciated.
2019 wholesale price Lan Cable Drawing Line - Aluminum / Aluminum Alloy Rod CCR Line – LINT TOP Detail:

1. Introduction

This production line produces round aluminum rod and aluminum alloy rod for electricians by adopting the technology of continuous casting and rolling.
The diameter of finished aluminum rod is Φ9.5mm, Φ12.5mm, Φ15mm.
This line has the advantages of high efficiency, low energy consumption, excellent quality of aluminum/aluminum alloy rod and so on.

2. Technical Parameters

Description

Aluminum Rod CCR Line

Aluminum Alloy Rod CCR Line 

Rolling type

Three-roll Y-type

Three-roll Y-type

Finished Rod Dia.(mm)

Φ9.5±0.2, Φ12.5±0.2, Φ15±0.2

Φ9.5±0.2, Φ12.5±0.2, Φ15±0.2

Line Speed(m/s)

6.2

6.2

Finished Rod Type

A2, A4, A6, A8,1350EC
8030, 8176 Aluminum rod

A2, A4, A6, A8, 1350EC
8030, 8176 Aluminum alloy rod
6201, 6101 Aluminum alloy rod

Capability(t/h)

4-4.5

4-4.5

Ingot Cross Section(mm2)

1500-2400

1500-2400

Furnace

Vertical melting furnace+Bale-out pot furnace

Vertical melting furnace+Circular holding furnace/Tilting holding furnace

Weight of Coiled Al(Alloy) Rod(t)

1.5-2.5

1.5-2.5

 

3. Al/Al Alloy Rod CCR Line

Aluminum  Aluminum Alloy Rod CCR Line


Product detail pictures:


Related Product Guide:

"Sincerity, Innovation, Rigorousness, and Efficiency" is the persistent conception of our company for the long-term to develop together with customers for mutual reciprocity and mutual benefit for 2019 wholesale price Lan Cable Drawing Line - Aluminum / Aluminum Alloy Rod CCR Line – LINT TOP , The product will supply to all over the world, such as: Lithuania, Lithuania, Hanover, Our Company policy is "quality first, to be better and stronger, sustainable development" . Our pursuit goals is "for society, customers, employees, partners and enterprises to seek reasonable benefit". We aspirate to do cooperate with all different the auto parts manufacturers, repair shop, auto peer , then create a beautiful future! Thank you for taking time to browse our website and we would welcome any suggestions you may have that can help us to improve our site.

FAQ

Q: Can I visit your factory?
A: All the customers from both home and abroad are warmly welcomed to visit our company and factory.

Q: Do you supply the installation and commissioning?
A: Yes, we do as followings:
-As soon as customer informed us the machines are put in the right place, we will send both mechanical and electrical engineer for machine start up.
-No-load testing: After machine installed completely, we make no-load testing first.
-With-load testing: Usually we will can produce 3 different wires to make load testing.
-Acceptance report: After the buyer confirms that machine can reach all specification under contract, the acceptance report will be signed for our record that machine will be in guarantee period.

Q: What information should I offer to get a detailed quotation from you?
A: For single machine: Usually we need to know inlet wire size, outlet wire size to be produced, productivity, pay off and take up size to choose the right machine.
For new cable plant or new cable production line, we need to know the datasheet of cables to be produced, the productivity, the standards to be followed, etc to design all machines needed.

Q: Can you supply the auxiliary equipment along with the machines?
A: Yes, definitely.
We has supplied heat exchanger, copper/aluminum powder filter machine, cooling tower, chiller, air compressor, drawing dies, pointing machine, cold welders, bobbins etc. with our machines.

Q: Could you do the design for the whole plant?
A: Yes, this is our advantage.
With the data sheet of cable to be produced, the standard your cables should follows, the productivity you expected. Our engineer on production technology and machinery will make design of production machines, test equipment, accessories like bobbins, dies, rewinding lines and materials needed.

Q: How can I know the status of my order?
A: We have our OA system on tracking the production.
For any of your request we can send photos and videos of your order, also we can use FACETIME to let you know the production.

Q: How do you work on the inspection before delivery?
A: We will make dynamic balance testing, levelness testing, noise testing, etc. during production.
After production finished, usually we make no-load running of each machine before delivery. Customers are welcomed to attend the inspection.

Q: What exhibitions will you attend, can we meet in the fair?
A: Dusseldorf International Wire and Cable Fair;
Wire South America Fair;
International Wire and Cable Fair in Shanghai;
International Istanbul Wire Fair, etc.
wire Southeast Asia Fair, etc.

Write your message here and send it to us